Home > Return Code > Vsam I O Return Code Is 116

Vsam I O Return Code Is 116

Contents

Refer to the section for Status-Key-1 being equal to "0" for additional information based on Status-Key-2. 1End of File, attempting to read beyond the end of the file. X'C4' 196 Return Code=08 Action=OPEN Access to data was requested via an empty alternate index. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. X'FC' 252 Return Code=>0 Action=CLOSE Automatic close of a DTF for a managed-SAM file failed. his comment is here

Return Code=04 Action=COMM An invalid control block address was specified in the {ACB|EXLST|RPL} = address parameter. Verify that a previous Access Method Service DEFINE or DELETE did not fail. PROGRAMMER ACTION: Rerun your job. PROGRAMMER ACTION: Change your job control EXTENT statement(s) to specify logical unit(s) which are valid for the partion and rerun the job, or remove the logical unit specification from the EXTENT

How To Resolve Vsam Open Return Code Is 168

Return Code=08 Action=Request VSAM received a return code from the LOCK macro indicating that there is no space in the lock table to make a lock entry. Equal to zero. Company Overview SimoTime Technologies was founded in 1987 and is a privately owned company. CONDITION CODE IS 12 IDC0002I IDCAMS PROCESSING COMPLETE.

Rerun the job. If the request was sequential or skip-sequential (but not direct), the file remains positioned for update or subsequent sequential retrieval. It is not valid in Concurrent Processing. Vsaminit Although the record is in the base cluster, VSAM cannot find it because the pointer to it is missing.

PROGRAMMER ACTION: Probable job control error. How To Resolve Vsam Open Return Code Is 232 Message 42261 will be issued at end-of-job step for this file. The information about volume is retrieved from the catalog, and programmer logical units are automatically assigned by VSAM. Possible causes:Attempting to WRITE or REWRITE a record that is larger than the largest, or smaller than the smallest record allowed by the RECORD IS VARYING clause of the associated file.Attempting

Register 0 contains the return code from CDLOAD. Vsam Error Codes Return Code=08 Action=Request An addressed request was issued for a relative-record file. Either: A programmer logical unit is not available in this partition (available programmer logical units have been used by ASSGN job control statements, or VSAM automatic assignments for files, catalogs or The information about volumes is retrieved from the catalog, and programmer logical units are automatically assigned by VSAM.

How To Resolve Vsam Open Return Code Is 232

Save the dump you obtain and SYSLOG output for later problem determination. The VERIFY command is not used to determine whether or not a file exists. How To Resolve Vsam Open Return Code Is 168 Alternatively a START or READ operation has been tried on an optional input file that is not present. 24 Relative and indexed files only. Vsam Open Return Code Is 160 MAXIMUM CONDITION CODE WAS 12 ******************************** BOTTOM OF DATA ********************************IEF237I JES2 ALLOCATED TO SYSOUT IEF237I JES2 ALLOCATED TO SYSPRINT IEF237I JES2 ALLOCATED TO SYSIN IEF142I ASNPG57V VERIFY - STEP WAS EXECUTED

Return Code=08 Action=OPEN The OPEN disposition specified for the file conflicts with other files characteristics. this content The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than expected, or an I/O error. PROGRAMMER ACTION: Use another program to load the file of specify ACB MACRF = NSR (non-shared resources) unit the file is loaded. PROGRAMMER ACTION: Compare your program's requirements and your job control statements to ensure that you have provided a corresponding DLBL statement for each ACB DDNAME. Idc3351i 118

  1. Return Code=08 Action=Request VSAM encountered end of file (during sequential retrieval), or the search argument is greater than the highest existing key (or relative record number) in the file.
  2. When next time a job/user tries to open the file for output, the file manager requests the catalog to turn on the flag.
  3. For example, a permanent I/0 error may have occurred when VSAM was reading or writing a catalog entry or catalog recovery area record.

This situation should only result from a system failure during UPGRADE processing. PROGRAMMER ACTION: Use LISTCAT to determine the volumes allocated to the file's primary allocation value, the file's USECLASS specification, and the space allocation status of these volumes. Only one processor may do output to SHAREOPTIONS(4) file at a time. weblink Make sure that the file-id specified in your DLBL statement meets the criteria for a valid VSAM file-id.

SimoTime Technologies shall not be liable for any direct, indirect, special or consequential damages resulting from the loss of use, data or projects, whether in an action of contract or tort, Iec161i X'42' 066 Return Code=08 Action=OPEN An attempt was made to open a DTF with file characteristecs that are incompatible with the file's cdharacteristics in the VSAM catalog. Return Code=08 Action=Request An attempt was made to store a record with a duplicate key, or a duplicate record was found for an alternate index with the UNIQUEKEY option, or a

X'A6' 166 Return Code=>0 Action=CLOSE The system lock table is not large enough to accommodate the concurrent requests.

These statistics cannot cause any processing error, but be aware that LISTCAT output may contain erroneous information. This document and the links to other documents are intended to provide a greater awareness of the Data Management and Application Processing alternatives. X'C8' 200 Return Code=08 Action=Request An addressed or control-interval access is attempted via a path. Idc3351i 108 Also, check to see if the path to the file concerned exists (Micro Focus). 14 Relative files only.

For example, a permanent I/0 error may have occurred when VSAM was reading or writing a catalog entry or a catalog recovery area record. Return Code=04 Action=CBMN Virtual storage available in the partition is insufficient to generate the requested block(s) or list(s) for GENCB. Preparing the application programs will require the transfer of source members that will be compiled and deployed on the target platform. check over here X'40' 064 Return Code=08 Action=OPEN An attempt was made to open a NOCIFORMAT file using an ACB.

X'4C' 076 Return Code=>0 Action=CLOSE Disposition processing failed during close. You requested a programmer logical unit that was not system generated, but whose assignment has been changed to UA (unassigned) by the operator or by a previous program. An EXTENT statement is required for each volume to be accessed; for example, for each volume on which your base cluster and alternate index(es) reside. X'FE' 254 Return Code=>0 Action=CLOSE CLOSE detected an unexpected rerun code from the lock manager.

If you specified the password in the ACB, change the specification to the correct password.