Home > Return Code > Vsam Catalog Return Code Is 248

Vsam Catalog Return Code Is 248

Contents

The error may be caused by such conditions as VSAM finding an unformatted recorded when expecting a formatted record, a volume containing data other than that expected, or an I/O error. Please try the request again. Save the dump you obtain and SYSLOG output for later problem determination. Return Code=08 Action=Request No record found. this content

This code can be issued for a file being accessed through a path if the pointer to the record is missing from the alternate index. PROGRAMMER ACTION: Rerun your job. PROGRAMMER ACTION: Only one OPEN, CLOSE, or Control Block Manipulation macro may use an ACB at a time. Return Code=04 Action=CBMN The block or list at the indicated address is not of the type specified in MODCB, SHOWCB, or TESTCB.

Vsam Return Codes

PROGRAMMER ACTION: Rerun the job when there is less concurrent activity in the system. Correct any errors and rerun the job. Return Code=08 Action=Request An attempt was made to retrieve a spanned record of a keyed-sequenced file with addressed access.

  • Return Code=08 Action=Request An invalid RBA has been specified.
  • PROGRAMMER ACTION: Rerun your job.
  • You have left off the catalog name and it's trying to define the file in the VSAM Master catalog or you have a DLBL for IJSYSUC in STDLABELs and that catalog
  • The operand must be specified.
  • You requested CNV mode on the RPL.
  • Verify that your program is using the correct catalog.

Rerun the job. I am trying to define a new file and getting the followingresponse. If this is a multi-step job, either divide it into separate jobs or provide ASSGN statements instead of simplified JCL. Vsam Feedback Codes X'6E' 110 Return Code=08 Action=OPEN You attempted to open for input only (ACB MACRF=IN) a file which was empty (no record in it) or a file was not properly closed on

X'0B' 011 Return Code=04 Action=COMM MODCB tried to modify an active RPL; the RPL must be inactive. Vsam Return Code 28 Save the dump you obtain and the SYSLOG output for later problem determination. If you do not use simplified job control, use LISTCAT output to determine which volumes must be described in the EXTENT statements. pop over to these guys Managed-SAM will simulate the open of an empty file for DTFSD TYPEFLE=INPUT requests.

If the system which opened the file has become inoperative, the lock can be released via Attention Routine UNLOCK command. (See VSE/Advanced Functions Systems Control Statements.) PROGRAMMER ACTION: Determine if the Vsam Return Code 13 Rerun the job. Equal to zero. X'FE' 254 Return Code=>0 Action=CLOSE CLOSE detected an unexpected rerun code from the lock manager.

Vsam Return Code 28

X'D8' 216 Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but the key length of the file being opened is greater than the maximum key length specified http://hercules390.996247.n3.nabble.com/idcams-for-vsam-td27965.html X'40' 064 Return Code=08 Action=OPEN An attempt was made to open a NOCIFORMAT file using an ACB. Vsam Return Codes X'71' 113 Return Code=00 Action=OPEN OPEN tried to execute the Catalog Check Service Aid in order to check the validity of this file's catalog records. Vsam Return Code 160 Reassign the programmer logical unit (ASSGN SYSxxx cuu) or request a device that is already assigned.

If the problem persists, instruct your operator to issue the ROD command and to run EREP (see VSE/Advanced Functions SADP); contact your IBM Support Center, and have EREP and SYSLOG output news The device on which the volume is mounted "down" (Job Control command DVCDN). PROGRAMMER ACTION: Because this information was collected during OPEN processing, it cannot be printed. PROGRAMMER ACTION: Consult with your system programmer to correct the problem. Vsam Extended Return Code Can Contain The Message

PROGRAMMER ACTION: Retry. IEB818I HIGHEST CONDITION CODE WAS 00000004 IEB819I END OF JOB IEBUPDTE. PROGRAMMER ACTION: If problems occur due to inconsistent extent information, display the VTOC and execute the Access Method Services LISTCAT command and compare the extent information. have a peek at these guys Do not specify REPLACE under these circumstances.

Return Code=08 Action=Request Invalid or conflicting RPL options or parameters: SKP together with BWD. Vsam Return Code 168 I am getting the below error. > > IDC3033I VOLUME RECORD NOT FOUND IN CATALOG > IDC3009I ** VSAM CATALOG RETURN CODE IS 248 >- REASON CODE IS IGG0CLBX-0 > IDC3003I Make sure that programmers logical units are available and rerun the job.

X'58' 088 Return Code=08 Action=Request Positioning error; the problem program: Issued a sequential GET without having VSAM positioned for this GET.

IDUMP output Storage dump of the supervisor lock tables A dump of the lock file if one was specified at IPL SYSLOG output job stream X'FF' 255 Return Code=>0 Action=CLOSE An PROGRAMMER ACTION: Have your program executed in a larger virtual partition. For shared resources, WRTBFR was issued, but: TRANSID was greater than 31,or The shared resource option (LSR) was not specified, or The LSR percentage value was not between 0 and 100. Vsam Rpl Feedback Codes PROGRAMMER ACTION: Use Access Method Services BLDINDEX command to initialize the alternate index.

X'84' 132 Return Code=08 Action=OPEN A permanent I/0 error occurred while VSAM was reading label information from the label information area. PROGRAMMER ACTION: If you expect the operator to specify the password, ensure that he has the correct password available. Issued a sequential PUT insert request for a relative-record file without having VSAM positioned for this request. check my blog If records were added, deleted, or update, consult the explanation to message 42251.

Run the Catalog Check Service Aid against the entire catalog; it will identify catalog errors for you. If you cannot correct the error situation, contact your IBM Support Center. Rerun the original job.