Home > Return Code > Vsam Catalog Return Code Is 118

Vsam Catalog Return Code Is 118


X'4F' 079 Return Code=08 Action=OPEN A catalog management error was detected during implicit define. The file is a SAM ESDS in non-CI format, so OPEN did not try to verify its catalog records. Merge the processing that was two ACBs so that only one ACB is required. (However, this can result in error code X'14' when the same situation occurs.) Run both ACBs under Not enough programmer logical units for this partition. have a peek at this web-site

X'58' 088 Return Code=08 Action=Request Positioning error; the problem program: Issued a sequential GET without having VSAM positioned for this GET. PROGRAMMER ACTION: Retry. PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center and have the dump output, SYSLOG output, and a copy of the job stream available for problem determination. X'FE' 254 Return Code=>0 Action=CLOSE CLOSE detected an unexpected rerun code from the lock manager.

Vsam Return Code

COM> Date: 2009-05-15 14:16:17 Message-ID: COL118-W40E3B75EB37824280C0F56CD5F0 () phx ! Return Code=08 Action=Request No record found. PROGRAMMER ACTION: If you are using a recoverable catalog, check that all required EXTENT statements are present and correct, and that sufficient storage is available. If you use the VERIFY command, this message can appear when VERIFY processing opens the data set.

  • Explain with example.Asked by: manideepOrganic chemistryExplain What is Organic Chemistry?Asked by: azamTable name and trigger nameCan we keep trigger name same as table name?
  • If you ignore the warning and try to process the data set, the results are unpredictable.
  • If the system which opened the file has become inoperative, the lock can be released via Attention Routine UNLOCK command. (See VSE/Advanced Functions Systems Control Statements.) PROGRAMMER ACTION: Determine if the
  • Return Code=08 Action=Request An attempt was made to change the prime key of a record that is being undated, or an attempt was made to change an alternate key that has
  • If the data set is opened for input, the catalog will not be updated by close and VERIFY will again be run by OPEN the next time the data set is
  • If authorization is granted, OPEN will complete successfully, assuming no other complications.
  • Disable Ad Blocker Learn More Login GeekInterview Login Create your GeekInterview account Signup Continue Reading after Disabling Refresh
  • BillyBoyo Global moderator Posts: 3773Joined: Tue Jan 25, 2011 12:02 am Hasthanked: 22 times Beenthanked: 257 times Top Re: VSAM Error/Warning messages by Robert Sample » Mon Aug 29, 2011
  • X'09' 009 Return Code=04 Action=COMM The work area provided in the program is too small to generate the requested block(s) or list(s) for GENCB or SHOWCB.
  • I want to prevent those messages. No space of the required class is available for additional secondary allocations. PROGRAMMER ACTION: The VSAM OPEN return code will be handled internally by the VSE/VSAM Space Management for SAM Feature by requesting operator authorization to delete the unexpired file. Idc3009i PROGRAMMER ACTION: Change your job control statement to either use simplified job control or to correctly assign device to accommodate the volumes required for the cluster and its associated alternate indexes.

    The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error. Vsam Open Return Code Is 232 X'47' 071 Return Code=08 Action=OPEN Allocation specifications for implicit define conflict with the file characteristics specified in the DLBL. An update of the record will update the status of all segments to a consistent level. If this does not work, rerun the job in a larger partition.

    Return Code=08 Action=Request An ERASE marco is issued for an entry-sequenced file (directly or via a path) or for a file for which control-interval processing has been specified. Iec161i The DTF implies a CI format file but the file is NOCIFORMAT. X'30' 048 Return Code=08 Action=OPEN An attempt was made to open a NOALLOCATION file which is not reuable (REUSE). X'CC' 204 Return Code=08 Action=Request The program issued a PUT to insert a record while in backward mode.

    Vsam Open Return Code Is 232

    PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. my site Only DTFPH may be used with NOCIFORMAT files. Vsam Return Code X'FC' 252 Return Code=>0 Action=CLOSE Automatic close of a DTF for a managed-SAM file failed. Vsam Return Code 168 Return Code=04 Action=CBMN Virtual storage available in the partition is insufficient to generate the requested block(s) or list(s) for GENCB.

    X'80' 128 Return Code=08 Action=OPEN The DLBL statement for the file or catalog is missing, or the file name specified in that statement does not match the name of the ACB. Check This Out Rerun the job. X'8C' 140 Return Code=08 Action=Request VSAM encountered an inconsistent spanned record (that is, one or more segments were incompletely updated to destroyed). PROGRAMMER ACTION: Recompile the progam with a larger work area specified. Vsaminit

    SYSOUT IEF285I AI00037.AI00037V.JOB52106.D0000101.? The following may be helpful for problem determination. Attemped to improperly switch between forward and backward processing. Source The error may be caused by such conditions as VSAM finding an unformatted recorded when expecting a formatted record, a volume containing data other than that expected, or an I/O error.

    PROGRAMMER ACTION: Restructure your program so that fewer files are open concurrently. Vsam File Status 35 During implicity deletion, the operator will be requested to authorize deletion if the expiration data previously specified for the file has not passed. X'C0' 192 Return Code=08 Action=OPEN The file to be opened for output was found to be unusable (catalog entry marked not usable) because (a) catalog recovery for this file failed, or

    The AMS program is used to create the VSAM files. (ii) The information...Asked by: irinak Just Answered MultiorgWhat is Multiorg?

    The VERIFY command can be issued via IDCAMS so just add a step at the front of the job to verify the datasets. For Local Shared Resources, the ACB addr is not same as for a previous request that used the same RPL. Robert Sample Global moderator Posts: 3156Joined: Sat Dec 19, 2009 8:32 pmLocation: East Dubuque, Illinois Hasthanked: 1 time Beenthanked: 190 times Top Next Display posts from previous: All posts1 day7 VSAM error codes which appear on the MVS job log and on the console. ******* you may copy this COBOL code and put it into your COBOL progrqam ******* to handle

    Ensure that the correct volume was mounted; check your job control statements defining the catalog of CRA for possible errors. However, if you do check the code for QSAM files, they return a subset of the codes shown below. PROGRAMMER ACTION: Have your program executed in a larger virtual partition. have a peek here The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than expected, or an I/O error.

    Not enough programmer logical units were available. X'E4' 228 Return Code=>0 Action=CLOSE The VSAM shared resoure table (IKQVSRT) ID is invalid. Rerun the job after the system problem is corrected. NOTE: VSAM provides an IDUMP of the region containing the VSAM control blocks, provided the SYSDMP is created and assigned.

    Redefine and reload the file. Return Code=08 Action=OPEN The system lock file is not large enough to accommodate the concurrent requests. Rerun the job. For example, you could cause lost records.

    Return Code=08 Action=Request An attempt was made to retrieve a spanned record of a keyed-sequenced file with addressed access. X'0B' 011 Return Code=04 Action=COMM MODCB tried to modify an active RPL; the RPL must be inactive. For Shared Resources, buffer pool is full. 016(10) Record not found. 020(14) Record already held in exclusive control by another requester. 024(18) Record resides on a volume that cannot be mounted. Possibly the wrong volume was mounted.

    Return Code=08 Action=Request The RECLEN value specified in the RPL was one of the following: Larger than the allowed maximum. An error occurred when the catalog was accessed during the processing of a CLOSE request. X'73' 115 Return Code=08 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a severe catalog error. Rerun the job.

    X'03' 003 Return Code=04 Action=CBMN An invalid keyword has been specified for GENCB/MODCB/SHOWCB/TESTCB. Return Code=04 Action=COMM An invalid control block address was specified in the {ACB|EXLST|RPL} = address parameter. The error flag (ACBERFLG) in the ACB (access method block) for the data set is set to 116 (X'74').Application Programmer Response: If the error occurred at a time other than during This code can also indicate that you attempted to load an empty file (using REPRO REPLACE) when the input file contained duplicate records.

    If the error was in the AIX during path access (RPL FTNCD=X'02'), the base cluster is not accessed, and no record is moved to the work area. Rerun the job after the system problem is corrected. The request would cause a sequence set record to be allocated whose RBA (within the index component) would be greater than 64511 multiplied by the size of the index control interval. and access GeekInterview anytime...